AOWEIDA
This 10-pack pairs black and white EVA foam sheets so the contrast you normally have to paint is already there. Every sheet is pre-cut to 9″ x 12″ and 2 mm thick, pressed at 86 kg/m³, with a smooth matte finish on both sides. Builders reach for this pack when a project needs a dark base and a light detail layer in the same session — armour plates with pale trim, letters on a dark board, or model parts that read as separate pieces without a paint job in between.
What Are Black and White EVA Foam Sheets?
These are pre-cut panels of closed-cell ethylene-vinyl acetate foam supplied in two contrasting tones in one pack. Each pack holds 10 sheets at 9″ x 12″ and 2 mm thick, sized to fit craft cutting machines, dies, and standard folders. Unlike loose craft foam bought by the metre, every sheet here is square, flat, and identical in gauge, so stacked layers line up along their edges. The mix is aimed at work that wants a dark and a light surface at the same time: cosplay armour with pale trim, display boards with readable lettering, stencils where the template and the finished part are cut from the same pack.
Product Specifications
- Product: Black and White EVA Foam Sheets (10 Pack)
- Material: EVA foam (ethylene-vinyl acetate), closed-cell
- Colours per pack: Black and white
- Sheet size: 9″ x 12″ (22.9 cm x 30.5 cm)
- Thickness: 2 mm, consistent sheet to sheet
- Pack quantity: 10 sheets per pack
- Finish: Smooth matte, both sides
- Density: 86 kg/m³ (high density)
- Cutting tools: Scissors, hobby knife, die-cut / cutting plotter machines
- Recommended adhesive: Contact cement or super hobby glue
- Heat-formable: Yes (heat gun or hair dryer)
Why Choose a Black and White Pack Over a Colour Assortment
1. Contrast you do not have to paint
Black against white is the sharpest pair you can get. Cutting both tones from one pack means trim, lettering, and inlay details arrive finished — no masking, no drying time, and no risk of a brush mark along the seam.
2. Every sheet the same 2 mm gauge
Consistent thickness means a white detail layer sits flush on a black backing sheet, which keeps layered signs, stacked stencils, and symmetrical parts from showing steps along their edges.
3. Pre-cut panels that drop straight onto a cutting mat
At 9″ x 12″ these squares fit standard plotter mats and most dies without trimming first. For repeat shapes in two colours, you can cut the whole stack in one pass.
4. Solid colour all the way through
The pigment runs through the sheet, so a cut edge, a sanded bevel, or a scored fold stays the same colour. Painted foam gives itself away along every edge; this does not.
5. A surface that still takes paint when you want it
Acrylics, markers, spray paint, and plastidip all sit well on the matte face. Start from black or white and paint only the parts that need it, instead of priming everything.
6. Closed-cell, water-resistant, easy to keep clean
The foam sheds water, springs back after bending, and wipes down after a messy session — useful for classroom sets that get handed around and for packaging inserts that need to look tidy on arrival.
Where Black and White Foam Sheets Work Best
- Cosplay armour and prop detailing — pale trim, straps, buckles, and insignias over a dark base plate.
- Displays, signs, and presentation boards — dark board, light letters, readable from across a room.
- Layered paper-craft style signs — two tones build depth without extra materials.
- Stencils and repeat templates — cut the template in white, the finished part in black.
- Model building, dioramas, and prototypes — facades, roofs, and roads that read as separate parts.
- Cards, scrapbook pages, and gift tags — dimensional layers where a light top on a dark shadow layer is the whole effect.
- Packaging inserts and protective pads — light-coloured contact surfaces over a dark support layer.
Cutting, Layering and Finishing Tips
Use the white sheets for templates and test cuts, then cut the black sheets for finished parts — any experimental marking lands on the side you can spare. A hobby knife or a plotter with a deep-cut blade handles 2 mm cleanly; score the surface before folding a tight curve. Heat-form pieces one at a time and let them cool flat before gluing, otherwise stacked layers creep as they relax. Contact cement suits full-surface bonds, while thin coats of super hobby glue are better for small details. Because both tones are the same gauge, you can dry-fit a two-colour layer and check the seam before committing glue.
Black and White Sheets vs Colour Assortment Packs
A multi-colour assortment gives you more hues, but usually two or three sheets of each, and the tones vary run to run. The black and white pack concentrates on the pair that does the most visual work and keeps it consistent: every sheet is the same size, gauge, and finish, and both tones hold contrast even after cutting and sanding. Choose an assortment when the design calls for a rainbow of colours; choose this pack when you need clean contrast, matched thickness, and repeatable results across a class set or a production run.
Frequently Asked Questions
How many black versus white sheets are in a pack?
Each pack holds 10 sheets in total, mixed between black and white. Standard packs balance the two colours; a different ratio can be arranged on wholesale orders.
Can I buy all-black or all-white packs instead?
Yes. Single-colour packs are available for large runs where one tone dominates. Tell us the quantity and we will quote both options.
Will markers bleed on the white sheets?
Fine-tip pens and markers sit cleanly on the matte surface. Test marker and paint on an offcut first, since solvent-based ink can feather slightly around the edges.
Can these sheets be layered for three-dimensional signs?
Yes. Identical 2 mm gauge keeps stacked layers even, so a two- or three-deep build sits flat with no gaps along the seam.
Is this foam heat-formable?
Yes. Gentle heat from a heat gun or hair dryer softens the sheet enough to curve it, and it holds the new shape once cool.
Can I use a Cricut or cutting plotter on 2 mm sheets?
Yes, with a deep-cut blade. Run a test shape first and adjust your machine’s material settings before committing a full sheet.
What sizes and thicknesses are available?
This listing covers 9″ x 12″ at 2 mm in a 10-pack. Other sizes, thicknesses, and bulk pack counts are available through wholesale.
Wholesale, Bulk & Custom – Factory Direct from AOWEIDA
AOWEIDA manufactures EVA foam in Dongguan, China. We supply wholesale quantities of black and white EVA foam sheets, colour assortments, rolls, and custom die-cut components, adjusting size, thickness, black-to-white ratio, and private-label packaging under OEM/ODM. MOQ is 200 pieces. Our factory is ISO 9001 certified and the material meets REACH and RoHS, so a school order of 200 packs and a retail rollout of 20,000 follow the same documented standard. Request a quote for custom EVA foam sheets.
Care & Storage
Store the pack flat and dry, out of direct sunlight, between 5–30 °C. Wipe sheets with a dry cloth before assembly — light-coloured foam shows workshop dust sooner than black. The closed-cell material is water-resistant but not intended for prolonged submersion, so seal it if parts will be used outdoors. If a sheet curls after long storage, press it flat under a light weight overnight.
